Chemical-free mold removal that leaves framing dry and ready to rebuild

Dry Ice Blasting Mold in HARBOR CITY, California

Dry Ice Blasting Mold in HARBOR CITY, California is the fastest way to strip mold off structural framing, attic sheathing and crawl space joists without soaking your house. We blast with frozen CO2 pellets that lift spores and residue off the wood, then HEPA-vacuum and treat what is left. If you have found black mold after a roof leak, plumbing drip or marine-layer damp, call us and we will scope it the same day.

↗
Fast online booking

Request service today

Tell us what is happening. Our local team will confirm your visit shortly.

No spam. No obligation. Just practical help.
Thanks — we'll call shortly to confirm your visit.
Dry Ice Blasting Mold by Mold Remediation Service Harbor City
Careful work. Honest options.
About this service

What Dry Ice Blasting Mold in HARBOR CITY, California Does

Dry Ice Blasting Mold in HARBOR CITY, California is a dry remediation method that fires rice-sized CO2 pellets at roughly -109°F through a pressurized blasting machine. The pellets hit mold, lift it off the substrate, and sublimate straight to gas on contact, so there is no water, no sand, and no chemical residue left behind. That matters on structural framing, where wet media like soda or sand can drive moisture deeper into the grain and set you up for a second bloom two weeks later.

HARBOR CITY sits close enough to the coast that marine-layer humidity parks on roofs and crawl space vents most of the year. Add a 30-year-old plumbing leak under a slab or a roof flashing failure from last winter's storms, and you get the classic call: musty odor in a hallway, dark staining on attic sheathing, or visible growth behind a bathroom wall. We handle dry ice mold removal HARBOR CITY California homeowners and property managers need before drywall goes back up, and we do it without tenting the house or hauling in a water truck.

  • ✓ No Secondary Water Damage
  • ✓ Reaches Tight Cavities
  • ✓ Kills Odor at the Source
  • ✓ Safe Around Wiring and Ducts
What's included

What Our Dry Ice Blasting Mold Service Includes

Every job includes the scope, containment, blasting, HEPA vacuuming, antimicrobial treatment and clearance testing. Rebuild and encapsulation are quoted separately once clearance passes, so you are not paying for drywall before we know the framing is clean.

✓

Full Scope and Photo Report

Moisture meter and thermal imaging camera readings, boroscope photos of wall cavities, and a written scope with square footage and affected materials. You get this within 2 hours of arrival.

✓

Containment and Negative Air

6-mil poly barriers, zip walls, a negative air machine with HEPA filters and a dedicated air scrubber. We keep spores inside the work zone so the rest of your house stays clean.

✓

Dry Ice Blasting of Framing

CO2 pellets at roughly -109°F strip mold off studs, joists, sheathing and subfloor. Pressure is tuned per substrate so we clean the wood without gouging it or driving moisture into the grain.

✓

HEPA Vacuum and Antimicrobial Fog

Every surface inside containment gets HEPA-vacuumed, then treated with an antimicrobial solution through a fogger. This knocks down anything the blaster loosened but did not remove.

✓

Post Remediation Mold Testing

Air samples and surface swabs collected after treatment, sent to an accredited lab, with results in 24 to 48 hours. If clearance fails, we re-clean at no charge.

✓

Debris Removal and Disposal

Saturated drywall, insulation and other porous materials that cannot be saved get bagged inside containment and hauled out. We leave the work zone broom-clean and ready for rebuild.

How it works

How Our Dry Ice Mold Removal Process Works

01

Inspection and Scope

We walk the property with a moisture meter and thermal imaging camera to map where water is still active and where the mold has spread. A boroscope goes into wall cavities and a HEPA vacuum samples the air. You get a written scope with photos, usually within 2 hours of arrival.

02

Containment Setup

We seal the work zone with 6-mil poly and zip walls, then set a negative air machine with HEPA filters so spores cannot drift into the rest of the house. A dedicated air scrubber runs the whole time. Setup takes 45 to 90 minutes depending on how many rooms are involved.

03

Dry Ice Blasting

Our technician suits up in personal protective equipment and works the blasting machine across the affected framing, sheathing and joists. Pressure is tuned per substrate. A typical attic takes 2 to 4 hours; a crawl space runs 3 to 5 hours because of access and ventilation.

04

HEPA Vacuum and Treatment

Once blasting is done, we HEPA-vacuum every surface in the containment, then apply an antimicrobial solution through a fogger. Porous materials that cannot be saved, like saturated drywall or insulation, get bagged and hauled out. This step runs 1 to 2 hours.

05

Verification and Clearance

We run post remediation mold testing with air samples and surface swabs, and hand you the lab report. If clearance passes, we can encapsulate the framing with an encapsulation coating and schedule rebuild. Most jobs clear on the first test.

Tools & methods

Tools and Methods We Use

Purpose-built equipment, used by trained technicians — so the job is done accurately the first time.

Dry Ice Blasting Machine

Fires rice-sized CO2 pellets at roughly -109°F to strip mold off framing, sheathing and joists without water or abrasive media.

Thermal Imaging Camera

Finds temperature differentials that reveal hidden moisture behind drywall, under flooring and inside wall cavities before we open anything up.

Moisture Meter

Confirms active moisture readings on wood, drywall and concrete so we know whether the source is still feeding the mold.

Boroscope

Slides through a 1-inch hole to inspect inside wall cavities and confirm the extent of growth before we set containment.

HEPA Vacuum

Captures spores and residue after blasting. Every surface inside containment gets vacuumed before we apply any liquid treatment.

Negative Air Machine and Air Scrubber

Keeps the work zone under negative pressure so spores cannot drift into living space. Runs from setup to final clearance.

Fogger

Applies antimicrobial solution as a fine mist to surfaces the blaster cannot reach, like the top plate of a wall or the back of sheathing.

Real results

Before and after.

Attic Sheathing After Roof Leak

Before

A 1,200 sq ft attic in Harbor Gateway had visible black mold across roughly 300 sq ft of sheathing after a roof flashing failure last winter. Moisture meter read 22% on the affected rafters, and the insulation below was saturated.

After

We contained the attic, blasted the sheathing and rafters with dry ice, HEPA-vacuumed the space, and treated with an antimicrobial. Post remediation mold testing cleared on the first sample. Moisture readings dropped to 11% within 48 hours.

Kitchen Wall Behind a Slow Leak

Before

A Wilmington bungalow had a musty odor for months with no visible growth. A thermal imaging camera found a slow supply line leak behind the kitchen wall, and a boroscope confirmed mold on roughly 40 sq ft of framing and backer.

After

We opened a small access hole, blasted the framing with dry ice, treated with an antimicrobial, and cleared the job with post remediation mold testing. The plumbing repair was coordinated before we closed up. No full tear-out was needed.

Crawl Space Joists After Slab Leak

Before

A Carson rental had a slab leak that soaked the crawl space for weeks. Joists and subfloor showed growth across roughly 600 sq ft, and the ground cover was holding standing moisture. Humidity in the crawl space read 78%.

After

We blasted the joists and subfloor with dry ice, HEPA-vacuumed the ground cover, treated with an antimicrobial, and installed a new vapor barrier. Post remediation mold testing cleared, and crawl space humidity dropped to 58% within a week.

Problems we solve

Mold Problems We Solve With Dry Ice Blasting

Most HARBOR CITY calls come down to one of these four situations. Each one has a different blast strategy, and each one gets clearance testing at the end.

Ask a pro →
01

Black mold on attic sheathing after a roof leak

We contain the attic, blast the sheathing and rafters with dry ice, HEPA-vacuum the insulation surface, and treat with an antimicrobial. If the insulation is saturated, we bag and remove it, then recommend a mold-resistant replacement.

↗
02

Musty odor with no visible growth

We run a thermal imaging camera and boroscope to find the moisture source, then open a small access hole and blast the framing directly. This avoids tearing out a whole room when only a 4-foot section is affected.

↗
03

Crawl space mold after plumbing or slab leak

We blast the joists and subfloor with dry ice, HEPA-vacuum the ground cover, and treat with an antimicrobial. We also flag the moisture source, whether that is a plumbing leak, poor ventilation or missing vapor barrier.

↗
04

Mold behind bathroom tile after a slow leak

We remove the affected tile and backer, blast the studs and subfloor with dry ice, treat with an antimicrobial, and reinstall mold-resistant drywall and backer once clearance passes.

↗
Proof you can check

Licensed, Certified and Documented

✓
IICRC Certified Mold RemediationInstitute of Inspection, Cleaning and Restoration Certification
✓
EPA Lead-Safe CertificationU.S. Environmental Protection Agency
✓
OSHA 10Occupational Safety and Health Administration
✓
ACAC Certified Microbial RemediationAmerican Council for Accredited Certification
✓
NADCA CertificationNational Air Duct Cleaners Association
Good questions

Frequently Asked Questions

(833) 929-5837 →

Most residential jobs run $1,200 to $4,500 in 2026, with a typical attic or crawl space landing around $2,200. Commercial spaces and multi-room losses go higher. Price depends on square footage of affected framing, access, and whether containment needs to span multiple floors. We quote flat after the scope, so you know the number before we start.

Yes. Dry ice blasting is non-toxic, non-conductive and leaves no chemical residue, so it is safe around wiring, plumbing and HVAC components. The CO2 sublimates to gas and vents out through our negative air setup. We still wear personal protective equipment and keep the work zone contained so spores do not migrate into living space.

A single-room job takes 4 to 6 hours from setup to clearance. A full attic or crawl space runs 6 to 10 hours, sometimes split across two days if containment is large. The blasting itself is fast; most of the time goes into setup, HEPA vacuuming and post remediation mold testing.

We do, and we cover the whole south bay from Downtown Harbor City out to Carson, Torrance, Gardena, San Pedro and Compton. Our trucks carry the blasting machine and HEPA equipment, so we are not waiting on a rental. Call (833) 929-5837 and we can usually scope the same day.

Ready when you are

Get Dry Ice Blasting Mold in HARBOR CITY, California Scheduled

We scope the job, quote a flat price, and blast the same week in most cases. Licensed through the CSLB, bonded and insured, with clearance testing included on every job. Call (833) 929-5837 and we will get a technician to your door.

Book a Scope (833) 929-5837 →
Request an appointment

Contact Our HARBOR CITY Mold Team

Call (833) 929-5837 and you will talk to someone who can actually schedule a crew, not a call center. We book same-day inspections for HARBOR CITY and the surrounding South Bay, and our emergency line stays open 24/7 for active water intrusion. Send photos to our email if you want a quick read before we arrive.

Request received — our team will be in touch shortly.
Tap to call(833) 929-5837